NOS derbi choke knob topper.

Stock derbi clutch spring. For flatreed, piston port, pyramid reed and stock hobbit too!

33.9mm length
10mm wide

Brake lever pinion screw for derbi brake levers and probably more!

m5 x .8 threads
6mm OD on barrel

NOS right side derbi sidecover.

Used CEV tail light bulb holder.

5mm Dellorto main jets in the 50's range: 50, 52, 54, 56, 58.  For use in all SHA and PHBG carbs

Black plastic throttle and matching 7/8 grip from Lusito.

1mm thick reducing shim for dellorto carburetors. Only works with 15.15 and 16.16 carbs.

21mm OD
19mm ID

Authentic Dellorto SHA made in Italy. Awesome upgrade carb for most bikes. Slap this on your motobecane, peugeot, puch, minarelli, garelli, sachs, morini or tomos and forget about it. This is the click choke version.

5mm Dellorto main jets in the 70's range: 70, 72, 74, 76, 78. For use in all SHA and PHBG carbs.

5mm Dellorto main jets in the 80's range: 80, 82, 84, 86, 88. For use in all SHA and PHBG carbs.

Authentic Dellorto SHA made in Italy. Awesome upgrade carb for most bikes. Slap this on your motobecane, peugeot, puch, minarelli, garelli, sachs, morini or tomos and forget about it. This is the click choke version.

Authentic Dellorto SHA made in Italy. Awesome upgrade carb for most bikes. Slap this on your motobecane, peugeot, puch, minarelli, garelli, sachs, morini or tomos and forget about it.

Stock tail light. This came standard on lots of bikes including puch and tomos. Fit this on pretty much any moped ever!

This uses 2x single filament bulbs.

original OEM CEV taillight with licence plate bracket.

very nice cause you can just mount your license plate right to it!

26mm x 1.5mm and 22 x 1.5mm flywheel puller for tons of Bosch flywheels - Puch, Kreidler, Tomos a3/a35, Batavus m56, Solo and Derbi Motoplat flywheels.

Super nice quality superman shape tail light for letting the folks behind ya know you're there.

Catch all the crud with these internal banjo filters for Dellorto SHA carbs. Fits 14-16mm carbs.

Super heavy duty universal ignition condenser for wiring externally. Get some new connectors if you need them.

Folding Pegs for you and a buddy. These mount over the rear shock bolt.

HPI CDI mini rotor ignition for all puch engines, e-50, za50, also tomos A35, tomos A55, derbi, sachs. Super curve with awesome 60w lights.

Puch e50 and za50 internal rotor CDI ignition system. Should fit all Puch, Tomos, Derbi and Sachs engines.

Clear fuel filter for standard 5mm fuel line.

Super awesome 5mm Tygon fuel line for all your fuel flowing needs.

Super awesome 5mm Tygon fuel line for all your fuel flowing needs.

Used but came off of a running bike. Comes with the cylinder, piston, piston rings and wrist clip. This bike was doing easily 35mph before I put a kit on it. You can slap this on and go.

Change your plug on the go with this 3/16" spark plug tool.

Used stock Derbi 13mm intake for the flatreed motor.

Used, kinda crusty original air box filter for any Derbi that's using the original SHA carb. These will clean up super nice and they all have the original foam element.

Used left side plastic engine cover for Derbi engines.

15 x 30 x 7 seal for derbi and sachs

index washers for 14mm spark plugs! comes with a variety of sizes for your tuning pleasures.

comes with two of each color!

red - 1.4mm thick
blue - 1.1mm thick
silver - 0.9mm thick
yellow - 0.7mm thick

Awesome 2 wire on/off ignition switch perfect for mopeds.

ADD TO CART TO CHECK STOCK!
NGK spark plugs. BHS series. Best in the world!

ADD TO CART TO CHECK STOCK!

NGK spark plugs. Resistor type short thread plugs.

NGK spark plug boot LB05FP. This is the resistor type that uses the little cap on the tip of the plug. 90 degree bend for those hard to reach places!

Small fuel filter for all mopeds. Perfect for tight spaces like moby or maxi!

Universal piston ring measuring 44mm x 1.5mm with a GI enclosure. Used on many many kits. Check yours to see if ya need this one.

Used on lots of 44mm airsal kits and alu kits for puch, tomos and derbi.

CDI stator plate for Puch e50 and za50, Sachs 505 and Derbi. You may have to flip the pick-up coil on the stator depending on what engine you're putting this on - no biggie!

CDI stator plate for Puch e50 and za50, Sachs 505 and Derbi. You may have to flip the pick-up coil on the stator depending on what engine you're putting this on - no biggie!

44mm 65cc Airsal cylinder kit for Derbi flatreed engines. The porting on this is awesome - 3 big transfers with 4 booster ports and a huge exhaust. Aluminum cylinder body with nikasil lining the bore.

Awesome upgrade Dellorto SHA carb for most bikes.

Trail Tech A/C Voltage Regulator. Stop blowing out those lights on kitted bikes! -Improved A/C Regulator with Adjustable Output.

Stock original reed block that comes with the Puch Gila 74cc cylinder kit. This will also fit Derbi flatreed 4 petal reed blocks, Aprilia rs50, Derbi GPR, Senda, and any Minarelli AM6 engine.

Yellow contra spring for the rear variator on derbi flatreed, pyramid reed and piston port engines. This is an upgrade from the stock spring, providing more resistance against variation which keeps the bike in a lower gear longer.

Big 21 tooth front sprocket for going fast fast fast on a Derbi Piston Port engine

Vintage line 38mm 50cc cast iron Metrakit cylinder for Derbi Piston Port engines. Includes piston, rings, wrist pin and clips and gasket set.

Performance exhaust pipe for Derbi Piston Port or Pyramid Reed engines on Variant frames. 22mm ID header.

Original 12,000 RPM CEV Derbi tachometer gauge for measuring your revvs.

Dual filament double contact BAY15D bayonet base bulb for moped tail lights. 13.5 Volt .69 Amp 9.32 Watt.