Universal ripcord kill switch to shut your bike off if/when you slide out at the track!

+30lbs of resistance from the stock spring for 1st and 2nd puch za50 and tomos clutches, saxonette clutches and m101 rear variators.

now available is a za50 super stuffy crank for the SMALL inner diameter clutch bell version of a puch two speed engine! previously unavailable and now here for you, fellow ruffians, environmentalists, hackers and tuners from around the globe

now available is a za50 super stuffy crank for the LARGE inner diameter clutch bell version of a puch two speed engine! now here for you, fellow ruffians, environmentalists, hackers and tuners from around the globe

Awesome quality puch race crankshaft and needle bearing made by DMP. Un-stuffed crank for super high rpms and wide powerband.

Stage6 R/T Carburetor, 21mm - scooter tech brought to the world of mopeds! Impressive-looking in black finish, the Stage6 R/T series carburetors are manufactured with extreme precision to ensure proper air and fuel flow throughout.

Wild performance Stage6 reed block and reeds for Honda Hobbits with DIO intake setups (or I guess for DIO's themselves, but who would have that?). Comes with .3mm reeds AND .4mm for ultimate tunability.

Tomos a35 and a55 unstuffed race crank from DMP. Awesome upgrade from your stock crank.

Aluminum stuffed performance crankshaft for puch e50 engines with roller bearing small end.

Red NGK racing plug boot and wire combo. Super insulated silicone for ultimate waterproofing. 7mm solid copper wire inner core with integrated 5K Ohm ceramic resistor spark plug wire. This is about the best spark plug boot money can buy. Comes with about 20" of wire.

HPI CDI mini rotor ignition for all puch engines, e-50, za50, also tomos A35, tomos A55, derbi, sachs. Super curve with awesome 60w lights.

HPI mini electronic CDI ignition for Honda Hobbit. Super bright 60w lights and curved CDI box.

Puch e50 and za50 internal rotor CDI ignition system. Should fit all Puch, Tomos, Derbi and Sachs engines.

The best moped 2 stroke oil money can buy. This is what we use in our race bikes and shop builds. The fully synthetic oil blend provides the ultimate lubrication for both stock and performance bikes. It burns cleaner with less smoke and reduces carbon build up in your ports and on your piston head.

PSR P6 exhaust for all flat port puch cylinders. Throw this on with your polini or AJH and blast to the moon.

PSR P8 exhaust for all angle port Puch cylinders.

Blue anodized clamp on aluminum velocity stack air filter for Dellorto PHBG carbs. 32mm ID.

Malossi adapter for using screw type exhausts on your Peugeot.

Mikuni vm18 Clamp Style Carb, so good it tunes itself.

Mikuni vm22 carburetor with bolt on flange mount and lever choke.

Top of the line performance carburetor for any high revving bike and definitely for all race bikes. 31mm OD spigot end. 44mm OD air filter end.

Mikuni VM20 2T carburetor with bolt on flange mount and manual pull choke.

43mm OD on air filter side. Roughly speaking, 42mm-44mm will also fit - some of our filters for this carb are actually marked 44mm like this one.

Don't forget to pick up some jets to tune it and and airfilter if ya need one.

Finally a super slick way to attach your registration sticker to your bike! This bolts over one of the bottom rear shock bolts, but you can put it wherever you like. Also, it's made out of aluminum, so it's easy enough to drill through if you want to put it somewhere else!

19mm DS  PHBG CLONE race carburetor. Spigot mount, easy access features.

19mm DS  PHBG CLONE race carburetor. Spigot mount, easy access features.

Stage6 Vforce3 8 petal reed block for Puch 74cc 47mm Gilardoni cylinders. Perhaps one the best performance upgrades you can make on your Gila kit. The amount of untapped power this releases is unparrelled.

Stage6 R/T Carburetor, 24mm - scooter tech brought to the world of mopeds! Impressive-looking in black finish, the Stage6 R/T series carburetors are manufactured with extreme precision to ensure proper air and fuel flow throughout.

One convenient rebuild kit for Sachs 504 and 505 clutches. Includes one set of Lucky2strokes performance Sachs clutch discs, one clutch gasket and one oil level bolt. Saves you a few bucks from buying them separate!

Koso temperature sensor + adapter for all radiator hoses with diameters between 14mm and 26mm. Comes in handy in case the thread of your thermometer does not fit. It can be used with Stage6 multimeters, Koso thermometers / multimeters or any Trail Tech H20 temp gauge.

The T-shaped adapter is placed between the radiator hoses. It comes with a temperature sensor and clamps.

Extra slim low profile digital voltmeter by Koso for checking the voltage coming out of your 12v CDI or battery. Compact, easy-to-read LCD display Displays voltage within 8-18V range. When the voltage is lower than 11.5V, the meter will flash to warn you.

Top of the line performance carburetor for any high revving bike and definitely for all race bikes. 33mm OD spigot end. 44mm OD air filter end.

Stock original reed block that comes with the Puch Gila 74cc cylinder kit. This will also fit Derbi flatreed 4 petal reed blocks, Aprilia rs50, Derbi GPR, Senda, and any Minarelli AM6 engine.

5mm intake spacer for Puch Gilardoni 74cc cylinders.

Stage6 R/T Carburetor, 28mm - scooter tech brought to the world of mopeds! Impressive-looking in black finish, the Stage6 R/T series carburetors are manufactured with extreme precision to ensure proper air and fuel flow throughout.

HPI regulator rectifier for keeping your lights from blowing out and for running and charging a battery.

HPI mini electronic CDI ignition for Garelli NOI. Super bright 60w lights and curved CDI box.

HPI mini electronic CDI ignition for Minarelli v1. Super bright 60w lights and curved CDI box.

Replacement piston for Puch Gila 74cc kits made by Vertex. Comes with piston, rings, wrist pin and clips.

This is a "A" piston - 46.96mm.

Puch 47mm 74cc Gilardoni race cylinder kit. This is a perfect example of flawless manufacturing and performance. Set this thing up right and you'll be getting pulled over for speeding faster than you can say "it was worth it."

Top of the line performance exhaust pip for MBK from Giannelli. This is the BLK GUN matte black baffle version. Comes with all the mounting hardware to bolt this up to an av7 or av10.

Chamber is now all black.

28mm VHST BS Dellorto carburetor. This carb uses the larger 6mm dellorto jets and has a slightly larger 6mm fuel inlet. This is a super moped race carb originally found on Derbi Senda & GPR, Aprilia shifty fifty's with Minarelli AM6 engines.

Rubber carb mount coupler for Mikuni TM24 carbs. Comes with two hose clamps specifically designed for this type of coupler.

ID - 28mm OD - 38mm

Rubber carb mount coupler for Dellorto PHBG and PHVA carbs. Comes with two hose clamps specifically designed for this type of coupler.

ID - 23mm
OD - 32mm

Search

Rubber carb mount coupler for OKO, PWK and some Mikuni carbs. Comes with two hose clamps specifically designed for this type of coupler.

ID - 32mm
OD - 42mm

Red 360mm - 380mm length rear shocks with a clevis end. The clevis mount is threaded for an m8 x 1.25mm bolt.

+2k RMP red clutch springs orginally for GY6 but these should fit honda hobbit, derbi piston port and pyramid reed, minarelli v1, etc. These springs are super universal and should fit on most bikes using this style ~30mm clutch springs.

High speed racing competition 7mm spark plug wire and boot made out of waterproof silicone. This is a must have for any race engine. Similar specs to the Atomic / NGK racing spark plug wire/boot setups, but a bit cheaper as this is the off brand! Save your pennies to spend on a kit or pipe or something, yep.

Blue 320mm - 340mm length rear shocks for any bike needing that length like puch magnum.

Blue 280mm - 300mm length rear shocks with a clevis end. The clevis mount is threaded for an m8 x 1.25mm bolt.

Red 280mm - 300mm length rear shocks with a clevis end. The clevis mount is threaded for an m8 x 1.25mm bolt.