Brake lever pinion screw for derbi brake levers and probably more!

m5 x .8 threads
6mm OD on barrel

Domino starter lever. Fits on most italian bikes, but no promises.

Black puch cable guide for all your maxi cable guiding needs.

Nice budget throttle option for savvy folks looking for the cheap alternative. This includes a grip yay! the throttle/perch and a brake stop knarp for your brake cable.

Black plastic throttle and matching 7/8 grip from Lusito.

Low rise 7/8 chrome handlebars. About 4" of rise on these guys with about a 2" backward rake and about 22" wide.

Universal "m" style 7/8" bars. About 22" from end to end.

Universal "m" style 7/8" bars. About 22" from end to end.

Rear brake cable for Puch and lots of other mopeds.

Black domino style throttle with bonus grip already installed. This is just like the throttles that came stock on lots of Italian mopeds. Super low profile throttle assembly for a nice clean look on your bars.

Black domino style rear brake lever assembly with bonus grip already installed. Super low profile assembly for a nice clean look on your bars. Spring loaded plastic brake lever, brake lever is about 5.7" long. Use these on any moped - 7/8 or 22mm handlebars.

Starter clutch cable for all mopeds equipped with the e50 engine.

Front brake cable for puch and pretty much every other moped.

Cable stop for magura controls. Sold individually.

mini cable knarp for moped cables. most people use these on their clutch or throttle ends.

measures M4 - 7mm long - 5mm OD

puch magnum style moped pedals!! these are 9/16" thread and will fit most mopeds!

long cable knarp for moped cables. works great for brakes

M6 - 15mm long - 8mm OD - 7mm

Black ROGUE tire tread pattern grips from ODI. 7/8 size for the left, 1" for the right/throttle.

Universal clamp on rear view mirror for all 7/8" handle bars. Black, round, and the stem is about 8" long.

Universal clamp on rear view mirror for all 7/8" handle bars. Black, square, and the stem is about 12" long.

Cushy gilled style grips from ODI. 7/8 size for the left, 1" for the right/throttle. These are Ian's new favorite grips.

Stock puch handlebar clamp. Fits on stock puch top plates likes and more! 32mm between the holes.

these come one at a time. so if you buy one, you get one. if you buy two, you get two. its the way of the world.

Super comfy medium soft grips with a half waffle pattern from ODI. 7/8 size for the left, 1" for the right/throttle. Pick your color!

Super rad cruise control thumb throttle assist. This slips directly over your throttle grip and allows you to just use one finger to control your throttle. A must have for rallys and long rides!

5mm cable housing end cap for capping the end of your cable housing. You need two of these per cable.

Find other custom cable makings here.

Clamp on domino style lever for 7/8 moped handlebars. Use this for clutch, choke or de-comp. The lever is about 2.5 inches long.

6mm pinch bolt for certain brake plate styles. You'll know if you need this.

original tomos speedometer cable for pre 2001 / 2003 model tomos mopeds.

this will usually fit A3 87-91 golden bullet, A35 92-06 targa, lx, sprint, tt, classic, bullet, and colibri. you must double check the measurements below tho to make sure this is what you need as tomos sometimes come with different configurations. A35 03-06 sprint and lx might use this cable that our friends at treatland have. instead so you must check! did you remember to check? good

about 760mm long

speedo cable threads are 10mm x 1mm at the small end and 12mm x 1 at the large end. Speedo cable inner square end is 2mm x 2mm

tomos part number - 213729

All four cables you need to completely re-cable your one speed puch e50. For maxi, magnum, pinto, freespirit, swinger, cobra anything with an e50!

Chrome plastic throttle assembly from Tommaselli. Comes with a matching set of grips. Fits on all 7/8" (22mm) bars.

Universal purpler rubber grip for any foot brake, clutch lever or kickstart lever.

-11mm ID
-16mm OD
-75mm total length but you can cut it to whatever length you need

Super nice quality master cylinder and front brake lever for any custom hydraulic brake set up. Works well on dirt bike conversion setups. Ben ran this master cylinder on his race bike.

All four cables you need to completely re-cable your one speed puch e50. For maxi, magnum, pinto, freespirit, swinger, cobra anything with an e50!

-(1x) throttle cable
-(1x) za50 starter cable
-(1x) front brake cable
-(1x) rear brake cable
-(2x) long knarp
-(1x) mini knarp

Black plastic 1/4" [6mm] cable guide clamps. Just bolt these onto your bike and run your cables through them to keep your cables neat and tucked away. Super pro solution for cable management. Sold individually.

Original OEM Puch internal tensioner for za50 motors. I'm sure you're all familiar with this thing. This moment of frustration brought to you by: Puch.

Nice budget rear brake control option for savvy folks looking for the cheap alternative. Has spring loaded brake lever, threaded hole for brake light switch and a non-threaded hole for a mirror.

Grab the lusito throttle control and you'll have a matching set yay!

Awesome black plastic throttle assembly. Great universal replacement for your old, worn out throttle.

Awesome black plastic throttle assembly. Great universal replacement for your old, worn out throttle.

Sachs clutch/decompression cable.

Super nice quality chrome metal throttle assembly for any custom moped project.

Awesome quality chrome low rise 7/8 inch / 22mm handle bars.

23.5 inch or 60cm speedometer cable for VDO speedos and drives.

stock puch maxi moped handlebars.

Stainless steel braided 34" hydraulic brake line for your custom moped project!

Super handy universal Magura clamp-on lever. This is traditionally used for starter clutches, but you can use it for choke or decomp or whatever you need. Fits 7/8 or 22mm handle bars.

Original motobecane left side rear brake control perch. In the nude. Get a matching NOS throttle perch to match!

Puch ZA50 clutch cable adjuster cover. These are 3D printed in black plastic by KONDO.

Original Kreidler decompression / clutch cable. The inner part of the cable is 42 inches long, the longer outer par of the cable is 32 inches long, and the smaller outer part is 4.5 inches long

NOS black domino left side control with spring loaded brake and clutch levers.

new old stoke choke / decompression lever for magura throttle assemblies found on many many mopeds!! these little guys were mostly found on sachs and peugeot in the US.