Black puch cable guide for all your maxi cable guiding needs.

Rear brake cable for Puch and lots of other mopeds.

Starter clutch cable for all mopeds equipped with the e50 engine.

Front brake cable for puch and pretty much every other moped.

Cable stop for magura controls. Sold individually.

mini cable knarp for moped cables. most people use these on their clutch or throttle ends.

measures M4 - 7mm long - 5mm OD

puch magnum style moped pedals!! these are 9/16" thread and will fit most mopeds!

long cable knarp for moped cables. works great for brakes

M6 - 15mm long - 8mm OD - 7mm

5mm cable housing end cap for capping the end of your cable housing. You need two of these per cable.

Find other custom cable makings here.

original tomos speedometer cable for pre 2001 / 2003 model tomos mopeds.

this will usually fit A3 87-91 golden bullet, A35 92-06 targa, lx, sprint, tt, classic, bullet, and colibri. you must double check the measurements below tho to make sure this is what you need as tomos sometimes come with different configurations. A35 03-06 sprint and lx might use this cable that our friends at treatland have. instead so you must check! did you remember to check? good

about 760mm long

speedo cable threads are 10mm x 1mm at the small end and 12mm x 1 at the large end. Speedo cable inner square end is 2mm x 2mm

tomos part number - 213729

All four cables you need to completely re-cable your one speed puch e50. For maxi, magnum, pinto, freespirit, swinger, cobra anything with an e50!

All four cables you need to completely re-cable your one speed puch e50. For maxi, magnum, pinto, freespirit, swinger, cobra anything with an e50!

-(1x) throttle cable
-(1x) za50 starter cable
-(1x) front brake cable
-(1x) rear brake cable
-(2x) long knarp
-(1x) mini knarp

Black plastic 1/4" [6mm] cable guide clamps. Just bolt these onto your bike and run your cables through them to keep your cables neat and tucked away. Super pro solution for cable management. Sold individually.

Original OEM Puch internal tensioner for za50 motors. I'm sure you're all familiar with this thing. This moment of frustration brought to you by: Puch.

Sachs clutch/decompression cable.

23.5 inch or 60cm speedometer cable for VDO speedos and drives.

Stainless steel braided 34" hydraulic brake line for your custom moped project!

Puch ZA50 clutch cable adjuster cover. These are 3D printed in black plastic by KONDO.

Original Kreidler decompression / clutch cable. The inner part of the cable is 42 inches long, the longer outer par of the cable is 32 inches long, and the smaller outer part is 4.5 inches long

Super stylin chrome puch cable guide for all your maxi cable guiding needs.

6mm x 1mm thread adjuster for front or rear brakes or clutch cables.

Universal replacement adjuster for brake or clutch cables. These fit up into the control perches.

Universal m5 cable adjuster. These usually thread into one end of a throttle cable bendy.

Dual knarp throttle cable for puch and lots of other bikes. You can also use this as a single knarp cable simply by chopping off the knarp that you don't need.

Super unique bolt for securing your brake levers to their perches. This is the m5 bolt with the plastic nut.

m5 bolt
m5 plastic nut
23mm overall length
9mm unthreaded part

Return spring for spring loaded magura brake lever controls. This is for the left side lever.

Return spring for spring loaded magura brake lever controls. This is for the right side lever.

Plastic nut for tensioning motobecane brake cables.

1.5mm ID and 5mm OD throttle cable housing for making custom cables. Sold by the foot! So measure your cables before buying!

Find the inner cable here.
Find more custom cable stuff here.

2mm ID and 6mm OD cable housing for making custom cables. Sold by the foot! So measure your cables before buying!

Find the inner cable here.
Find more custom cable stuff here.

6mm cable housing end cap for capping the end of your cable housing. Kinda like a palindrome mayybeee? You need two of these per cable.

Find other custom cable makings here.

1.5mm inner cable housing for making custom cables. This size is best used for throttle cables, choke cables and maaaaaybe even decomp cables.

Sold by the foot.

Find the outer housing for it here.
Find other custom cable makings here.

2mm inner cable housing for making custom cables. This size is best used for front and rear brake cables and maaaaaybe even decomp cables.

Sold by the foot.

Find the outer housing for it here.
Find other custom cable makings here.

M6 thread slotted cable adjuster. Some controls require this kind of adjuster, you'll know if you need it! Threaded part of the bolt is 19mm long.

Derbi control cable holder. For stopping those rowdy cables.

m6 nut for threaded brake cable ends. Usually found on General, Lazer, Sachs, Trac etc.

The inner wire of a sachs clutch/decomp cable. Super handy replacement part.

General or Lazer Front brake cable.

New old stock rear brake cable for general or lazer mopeds. This one has wires that hook up to the brake light. Weird.

This is the little bit of cable that goes in between the de-comp and the case on sachs engines.

Original rear brake cable for Trac mopeds and definitely many more!

Plastic magura starter lever, you know the one you always break when you pull too hard. Fits Puch Maxis and many other mopeds too!

Starter clutch cable for puch za50 two speed engines.

M6 thread slotted cable adjuster. Some controls require this kind of adjuster, you'll know if you need it! Threaded part of the bolt is 25mm long.