NOS derbi choke knob topper.

oem original bing jets for use in square bing carburetors found on sachs and korado mopeds!

5mm Dellorto main jets in the 50's range: 50, 52, 54, 56, 58.  For use in all SHA and PHBG carbs

1mm thick reducing shim for dellorto carburetors. Only works with 15.15 and 16.16 carbs.

21mm OD
19mm ID

Float needle for 12mm - 15mm bing carburetors.

5mm Dellorto main jets in the 70's range: 70, 72, 74, 76, 78. For use in all SHA and PHBG carbs.

5mm Dellorto main jets in the 80's range: 80, 82, 84, 86, 88. For use in all SHA and PHBG carbs.

Catch all the crud with these internal banjo filters for Dellorto SHA carbs. Fits 14-16mm carbs.

Blue anodized clamp on aluminum velocity stack air filter for Dellorto PHBG carbs. 32mm ID.

Round throttle slide for 12mm, 14mm and 15mm round bing carburetors.

Replacement metal float pin for Dellorto PHVA carburetors.

clear float bowl for phbg carburetors. made by malossi. easy screw jet access.

30 3339

Hand pull choke for Dellorto PHBG carbs. Fits all size PHBG's and the PHBG clone carbs. This just threads into the hole on the top of the carb. Way easier than the cable choke for sure!

Cable choke assembly for a Dellorto PHBG carburetor.

Fuel filter for the 13mm Dellorto SHA carbs that you'd find on Vespa and Kinetic.

Replacement flot bowl gasket for round bing carbs 12mm-15mm.

two gaskets, one for either side of the fuel inlet or banjo on your bing carburetor.

they measure 12mm OD and 8mm ID and will work with bing carburetors 12mm through 15mm varieties with the banjo style fuel inlet.

Bing carb gasket rebuild set. Includes one float bowl gasket, one top gasket, and two banjo gaskets.

New float bowl for 12mm - 15mm round bing carbs.

OEM float / float needle for Motobecane Gurtner carburetors.

Original short cock knob for derbi variant mopeds.

bing carburetor top gasket

for 12mm to 15mm found on most puch mopeds

Rubber carb mount coupler for Mikuni TM24 carbs. Comes with two hose clamps specifically designed for this type of coupler.

ID - 28mm OD - 38mm

Rubber carb mount coupler for Dellorto PHBG and PHVA carbs. Comes with two hose clamps specifically designed for this type of coupler.

ID - 23mm
OD - 32mm

Search

Rubber carb mount coupler for OKO, PWK and some Mikuni carbs. Comes with two hose clamps specifically designed for this type of coupler.

ID - 32mm
OD - 42mm

Rubber carb mount coupler for spigot mount carbs. Super heavy duty version from Doppler. Comes with two hose clamps.

-24mm ID for PHBG.

5mm Dellorto main jets in the 60's range: 60, 62, 64, 66, 68. For use in all SHA and PHBG carbs

5mm Dellorto main jets in the 90's range: 90, 92, 94, 96, 98. For use in all SHA and PHBG carbs.

Main hex jet for D slide OKO, Keihin and all PJ, PWK and PD carburetors.

These do not work on the OKO PE carbs.

Idle jets for D slide OKO, Keihin and all PJ, PWK and PD carburetors.

These do not work on the OKO PE carbs.

malossi throttle 90 degree cable bendy adjuster

angle your throttle cable where you wish

for bing carburetors 12mm through 17mm and all dellorto carburetors, SHA, PHBG, PHVA and mikuni and more.

26 3997

cable end is M6 x 0.75mm threading

Float needle for Dellorto SHA and PHBG carbs.

Replacement gasket for a dellorto SHA float bowl.

NOS derbi choke knob bobber.

NOS derbi choke knob shaft.

Cork float gasket for square bing carburetors.

The little gasket that goes underneath the top of a square bing carburetor.

1.5mm thick reducing shim for dellorto carburetors. Works with 14.12, 15.15 and 16.16 carbs.

21mm OD
18mm ID

Carb top for Dellorto PHVA carbs. Double check to make sure this is the style top that you need.

Replacement lever for dellorto PHVA carburetors.

Replacement float bowl for Dellorto PHVA carburetors.

Dellorto PHVA carburetor throttle slide for 12mm and 14mm carbs. These are number 40 slides.

23mm tall
15mm OD

Float for Dellorto SHA carbs size 14-16mm.

Choke plate for SHA carburetors. Fits 14mm - 16mm carbs.

Choke return spring for SHA carburetors. Fits 14mm - 16mm carbs.

Used float filter for square bing carburetors.

Metal plate that bolts inside sachs airboxes on square bings.

Needle clip for square bing carburetors.

Carburetor top for square bing carbs. Kind of like a top hat.

Banjo for bing carburetors. Where the fuel goes in. Dee dee de de de de de de daaaa.