Stock derbi clutch spring. For flatreed, piston port, pyramid reed and stock hobbit too!

33.9mm length
10mm wide

+25lbs of resistance from the stock spring for 1st and 2nd puch za50 and tomos clutches, saxonette clutches and m101 rear variators.

+30lbs of resistance from the stock spring for 1st and 2nd puch za50 and tomos clutches, saxonette clutches and m101 rear variators.

Gotta shave weight wherever you can if you wanna go fast. This is a great step towards increasing the power output from your bike! This will help distribute the oil more evenly over your clutch pads increasing their life while keeping them cooler.

Cheap effective universal puller for lots of bikes - e50, v1, m1 & m01, use it to pull an hpi etc.

One of the best, easiest upgrades for a puch 2 shoe or 3 shoe clutch. Super stiff for lots of low end slip.

e50 clutch bell. Regular cut gear. Used. Used. Used.

Minarelli v1 clutch retaining clip used to keep starting plates locked in.

New OEM clutch bell for tomos a35 and a55 engines.

this is compatible with all tomos A35 and A55 engines. not A3 though!

223423

Set of three Tomos A35 and A55 clutch pad shoes, enough to re-pad one first gear Tomos clutch. Cork lined for your pleasure. Fun fact: Tomos 1st gear clutch shoes show the pad material through a small window on the bottom side.

If you need one of two pads, we also have sell them individually.

Pressure cup for sachs starter clutch mechanism. Or ashtray. You decide.

Used v1 internal main drive gear. Angled gears for use with angled gear clutch bells. Be sure to get a crown nut for this if you need it.

Minarelli v1 pedal shaft, just in case you bent, broke or lost yours!

original OEM tomos A35 A55 2nd gear clutch

227019

riginal OEM tomos A35 + A55 1st gear clutch!

the A35 and A55 both use the same 1st gear clutch so there's two different part numbers!

227018 - A35
227849 - A55

This is a must have if you're running a Doppler ER variator. This replaces and upgrades your original pulley and adds clutch function to your ER variator.

Used clutch disk for sachs clutches. This is 2.5mm thick.

One convenient rebuild kit for Sachs 504 and 505 clutches. Includes one set of Lucky2strokes performance Sachs clutch discs, one clutch gasket and one oil level bolt. Saves you a few bucks from buying them separate!

Minarelli v1 regular [right hand] threaded clutch nut. Check to make sure you don't need the reverse thread clutch nut!

Used Sachs 504 and 505 metal clutch spring.

Original clutch side crankshaft nut for sachs engines.

Clutch disc for sachs clutches. Clutch clutch clutch. What does it even mean anymore.

Hub for sachs clutches. Looks like a mini skate ramp.

Weird roundish, squarish washer for sachs. What does it do? What are its mystical powers?

This spring returns the starter lever to its resting position on sachs clutches.

clutch bell for sachs motors - 504 and 505.

Starter clutch pin bolt for Sachs engines.

Used puch za50 clutch starter plate.

Original OEM Puch internal tensioner for za50 motors. I'm sure you're all familiar with this thing. This moment of frustration brought to you by: Puch.

Used puch za50 second gear clutch.

Used puch za50 first gear clutch.

Used puch za50 second speed driving plate. 22 teeth.

Used puch za50 clutch engaging plate.

Used puch za50 clutch bell. This has a 10.3mm id for the shaft and 16 teeth on the gear.

this is a used part from an original puch za50 two speed engine. may be a little worn from being in some moped of the past but it is a functioning engine part. no complaining!!

uses the 16100 bearing

**unfortunately this version will not fit on the za50 super stuffy crank without changing out the 16100 the bearing**

PLEASE NOTE ** this one we have right now is in nice shape! much better than the photo.**

e50 clutch retaining clip. Use this to keep all your clutch components from spinning off the shaft and gettin crazy.

Used puch clutch cover for your e-50. We get these in from time to time so the picture is of a similar item. Just know you'll get a used cover in good condition.

OEM replacement starter clutch plate for puch e50 clutches. You're gonna have to re-use your original thrust washer bearing and pin on this one though!

Used puch za50 clutch bell. This has a 9.6mm id for the shaft and 16 teeth on the gear.

Lightly used OEM three shoe clutch for Puch e50 engines. Super upgrade from your worn out 2-shoe.

Puch ZA50 clutch cable adjuster cover. These are 3D printed in black plastic by KONDO.

Used puch e50 starter clutch plate.

e50 clutch bell. REVERSE cut gear. Used. Used. Used.

Puch E50 Moped Engine 2-Shoe Centrifugal Clutch. This clutch is in great shape with all the the pad material intact. Picture is of similar item - we have more than one of this item in stock and item shipped will be in equal or better condition.

Lightly used OEM three shoe clutch for puch e50 engines. This clutch is in great shape with all the the pad material intact. Picture is of similar item - we have more than one of this item in stock and item shipped will be in equal or better condition.

New OEM three shoe clutch for puch kickstart engines. Kickstart engines only!

Tomos 1st gear clutch segment for A35 and A55 clutches. Cork lined for your pleasure. Fun fact: Tomos 1st gear clutch shoes show the pad material through a small window on the bottom side.

These are sold individually so if you need to re-shoe one clutch, you'd need 3 pads, or just get the whole set.

OEM replacement rubber donut clutch for the one speed Garelli NOI engines. Get em before they're gone again.

15% stiffer clutch springs for sachs 505 mopeds from OB1, plenty of info to be found on these on their blog.

+20lbs of resistance from the stock spring for 1st and 2nd puch za50 and tomos clutches, saxonette clutches and m101 rear variators.